Skip to content

Flysky FRM303 — model slots, binding, receiver output

Got the FRM303 wired to Magic Box and its LED slowly flashing blue? Then the cable side is done (wiring and PPM setup). This page covers the module side: the FRM303 remembers 10 models, and each one has its own binding, receiver output and failsafe. Easy to miss: bind a second model without switching slots and it quietly replaces the first.

Everything is set with the five-way key. Hold a direction for 3 seconds to open a menu; you’ll hear a click when the module accepts it.

Hold 3 sLEDMenu
RightwhiteModel slot (and receiver search)
CentermagentaRF system & binding
LeftcyanReceiver output protocol
DownredFailsafe
UpyellowOutput power

Inside a menu the number of flashes is the option number. Up / Down steps through options, Center 3 s saves, Left exits. (Holding Up while powering on is a different menu — the input signal type from the wiring page.)

Each of the 10 slots stores:

  • the RF system (Classic or Routine, one-way or two-way),
  • the receiver ID — two-way binding only,
  • the receiver output protocol,
  • the failsafe.

Check or change the active slot: hold Right 3 s — LED turns white. Count the white flashes: 1–5 = slot 1–5. Slots 6–10 add one blue flash to the white ones: one white + one blue = slot 6, up to five white + one blue = slot 10. Up / Down to pick another, Center 3 s to save, Left to exit.

Find the slot by switching the model on: hold Right 3 s (white), then push Right again — LED flashes blue fast. Power up the model. The module walks through the slots, stops on the one bound to that receiver and turns solid green. Works only for two-way binding — a one-way receiver never answers, so the search keeps cycling until you push Left.

  1. Select the slot you want (see above).

  2. Hold Center 3 s — LED turns magenta. Flashes = RF system:

    FlashesRF system
    1Classic 18CH, two-way
    2Classic 18CH, one-way
    3Routine 18CH, two-way
    4Routine 18CH, one-way
  3. Up / Down to pick, then push Right — LED flashes green fast, the module is binding.

  4. Put the receiver into bind mode. On the INr6-HS: hold BIND while powering it on, or hold BIND 3 s on a receiver that’s already on. Its LED flashes fast.

  5. Two-way: the module LED goes solid green — done. One-way: the module can’t tell it worked; watch the receiver — its LED drops from fast to slow flashing. Then push Left on the module to exit.

Not every receiver binds on every system. From our bench: the FTr10 binds only on Classic, the INr6-HS only on Routine. Flysky’s FRM303 manual lists the FTr4, FGr4P, FGr4s, FTr16S, FGr4 and FTr10 as Classic receivers. The INr6-HS manual adds that the RF library version on the transmitter and the receiver must match.

Won’t bind? Before you suspect the hardware: make sure the receiver LED is flashing fast (it really is in bind mode), then try the other system.

The FRM303 sets what the receiver puts out to your model — it’s stored in the slot, not on the receiver.

Hold Left 3 s — LED turns cyan: 1 PWM · 2 i-BUS out · 3 S.BUS · 4 PPM. Up / Down, Center 3 s to save.

  • Two-way: applies straight away.
  • One-way: takes effect only at the next binding — set it before you bind.

This is the one that catches people:

  • Classic receivers with two settable ports (FTr10, FTr16S, FGr4) — S.BUS comes out of the port labelled i-BUS. CH1 stays PWM.
  • Receivers with Newport ports (INr6-HS) — S.BUS comes out of NPA. On the INr6-HS that’s the CH6 port.

“I don’t use i-BUS, so I left that port empty” — and on an FTr10 that’s exactly where your S.BUS was. Other receivers: check their manual for which port carries the bus.

Hold Down 3 s — LED turns red:

FlashesOn signal loss
1No output
2Hold last values
3Fixed values — the ones Magic Box is sending when you save

For option 3, put the sticks where you want them (throttle at idle) before you save. On S.BUS and PPM “no output” can’t drop single channels, so it holds the last values instead — but S.BUS also carries a failsafe flag, and a flight controller reads that. A plane on plain PWM servos without an FC: option 3. Test it on the bench, prop off — switch the module off and watch what the model does.

Hold Up 3 s — LED turns yellow: 1 = 25 mW · 2 = 100 mW · 3 = 500 mW · 4 = 1 W · 5 = 2 W.

The ceiling depends on how the module is powered: USB-C caps it at 25 mW, the internal battery at 500 mW, XT30 external power allows the full 2 W. It also depends on firmware — Flysky publishes FCC (up to 1 W) and Developer (up to 2 W) builds. Don’t fly on USB-C power. Flysky ships the module at ≤ 20 dBm (100 mW) and leaves the rest to local rules — check what’s allowed where you fly.

On this link channel 14 at the receiver carries signal strength (RSSI), not what Magic Box sends on CH14. Don’t map anything to CH14 in your Magic Box profile. Flying with an INAV flight controller? Set rssi_channel = 14.