Skip to content

Trimming a Plane with iNav

This page is for fixed wings with an iNav flight controller in the chain. If your receiver drives the servos directly (classic line-of-sight, no FC), Magic Box trims shift the servo centre like on any radio — nothing below applies.

  • You trim an axis with Magic Box trims (a hat bound as trim) or with your radio’s trims, then let go.
  • iNav Configurator, Receiver tab: the channel holds still.
  • Outputs tab: the servo value keeps creeping, fast, in one direction, with the model sitting on the bench.
  • Switch to MANUAL: the creep is gone.

A channel that holds still in the Receiver tab means Magic Box is sending a steady value. The creep happens inside the flight controller.

In every stabilised mode (ACRO, ANGLE, HORIZON) iNav reads a stick offset from centre as a request: a rotation rate in ACRO, a bank or pitch angle in ANGLE. To iNav, a trim is the stick sitting slightly off centre.

On the bench the plane can’t rotate, the gyro reads zero and the error never closes, so the integral (I) term keeps winding up until it hits its limit. That’s the creep in the Outputs tab. In the air the same trim is a constant request to roll (ACRO) or to hold a slight bank (ANGLE), and the stabilisation works against it.

MANUAL skips the PID controller: the output follows the stick and a trim is a plain centre offset.

This is how iNav treats trims in stabilised modes, with any radio. For an iNav plane the trim belongs in the servo midpoints, and the transmitter trims go back to zero. Three ways to get there are below.

Full control: you see every number before it goes in. The price is that a typo goes in too, so double-check each value.

  1. Fly in MANUAL and trim with the Magic Box trims until the plane flies straight and level hands-off.
  2. Land and disarm. Leave the trims where they are.
  3. Connect iNav Configurator. Keep the flight mode switch on MANUAL, sticks centred, trims still in.
  4. Open the Outputs tab and note the live value of each servo.
  5. Enter each noted value as that servo’s midpoint and save.
  6. Set the Magic Box trims back to zero. With MANUAL and sticks centred, each servo should sit on the value you noted.

The values are per servo, so this works with mixes too (elevons, V-tail): every servo gets its own midpoint.

Option 2 — SERVO AUTOTRIM on a dedicated switch

Section titled “Option 2 — SERVO AUTOTRIM on a dedicated switch”

iNav can move your trims into the midpoints for you. It saves typing numbers by hand, but the moment you flip the switch decides whether it is safe — flipping it in flight in MANUAL has crashed more than one of our own planes. Read how it works before you use it.

  • It works only while armed, in any flight mode, MANUAL included. iNav will not arm while the switch is on.
  • Switch on: iNav averages the real output of every roll, pitch and yaw servo for 2 seconds.
  • After those 2 seconds the averages become the new midpoints straight away. They are written to the flight controller’s memory only when you disarm.
  • In MANUAL the averaged output contains your trim. From that moment the trim counts twice — once inside the new midpoint, once still in the Magic Box — until you centre the trims. On the ground that is a small servo jump. In the air it is a sudden pitch or roll.
  • Switch off before disarming: the old midpoints come back and nothing is saved.
  • Continuous servo autotrim (feature FW_AUTOTRIM) must be off. With it on, the switch is not offered in the Modes tab. AUTOTUNE active at the same time also blocks the switch.
  1. Assign SERVO AUTOTRIM to its own switch in the Modes tab. Continuous autotrim off.
  2. Arm with the switch off.
  3. Climb to a safe height. Fly in MANUAL and trim with the Magic Box trims until the plane flies straight and level hands-off.
  4. Land in MANUAL and stay armed. Leave the trims where they are.
  5. On the ground, sticks released: switch on. About 2 seconds later the servos jump slightly — the trim is now inside the midpoints.
  6. Disarm with the switch still on — that is the moment the midpoints are saved.
  7. Centre the Magic Box trims and switch off. On the bench, in MANUAL, check the servos sit where the plane flew straight.

In ACRO or ANGLE the mode can be used in flight: trims at zero, switch on in straight and level flight, hold it for 3 seconds, land and disarm. There is no double trim, because iNav averages its own stabilisation correction and resets it once the midpoints change.

Option 3 — iNav config generated by Magic Box

Section titled “Option 3 — iNav config generated by Magic Box”

In development: Magic Box will generate an iNav config that shifts the servo midpoints by your current trims, so the trims can go back to zero without typing numbers by hand. No release date yet — until then, use Option 1 or 2.

Danger zone: the first MANUAL flight on a new plane

Section titled “Danger zone: the first MANUAL flight on a new plane”

Stabilisation hides a bad CG and wrong control throws. A new plane can fly beautifully in ACRO or ANGLE and badly in MANUAL — and both trimming options above start with a MANUAL flight.

  • Before the first MANUAL flight, check the CG and the control throws in MANUAL on the bench.
  • Make the first switch to MANUAL high, with a hand ready to flip back to ANGLE or ACRO.

Anything without stabilisation between the receiver and the servos: a classic receiver wired straight to servos, a sim rig, or MANUAL mode on an FC. There a trim is a centre offset and nothing creeps. Setups side by side: What You Need.

Behaviour described on this page holds for iNav 6.1 through 9.1. Stuck on a specific airframe? Ask in the community group.